Denon AVR-1613 Bedienungshandbuch PDF herunterladen (Seite 87)

Audio

Audyssey

Default settings are underlined.

Set Audyssey MultEQ

, Audyssey Dynamic EQ

and Audyssey Dynamic Volume

. These can be

selected after Audyssey

Setup has been performed. For additional information on Audyssey technology,

please see page117.

NOTE

•If you have not performed Auto Setup, or if you change the speaker settings after performing Auto Setup,

you may not be able to select Dynamic EQ

/Dynamic Volume

In this case, either perform Audyssey

Setup over again or perform “Restore...” (vpage 26) to

return to the settings after Audyssey

Setup was run.

•When HD Audio for which the sampling frequency exceeds 96 kHz is played back, the “Audyssey”

cannot be set.

Setting items Setting details

MultEQ

compensates for

both time and frequency

characteristics of the

listening area based on

Audyssey

Setup

measurement results.

Selection is done from three

types of compensation

curves. We recommend the

“Audyssey” setting.

MultEQ

is the prerequisite

function for Dynamic EQ

and Dynamic Volume

Audyssey : Optimize the frequency response of all speakers.

Audyssey Byp.L/R : Optimize frequency response of speakers except

front L and R speakers.

Audyssey Flat : Optimize frequency response of all speakers to ﬂat

response.

Manual EQ : Apply frequency response set with “Manual EQ”

(vpage85).

Off : Turn “MultEQ

” equalizer off.

•“Audyssey”, “Audyssey Byp. L/R” and “Audyssey Flat” can be

selected after Audyssey

Setup has been performed. “Audyssey”

is automatically selected after performing Audyssey

Setup. When

“Audyssey”, “Audyssey Byp. L/R” or “Audyssey Flat” is selected,

illuminates.

•After running Audyssey

Setup, if the Speaker Conﬁguration, Distance,

Channel Level, and Crossover Frequency have changed without

increasing the number of speakers measured, only illuminates.

NOTE

When using headphones, “MultEQ

” is automatically set to “Off”.

“MultEQ

”, “Dynamic EQ

” and “Dynamic Volume

” settings are stored for each input source.

Setting items Setting details

Dynamic EQ

Solve the problem of

deteriorating sound quality

as volume is decreased

by taking into account

human perception and

room acoustics. Works with

MultEQ

On : Use Dynamic EQ

Off : Do not use Dynamic EQ

is displayed when set to “On”.

NOTE

When the menu “Dynamic EQ

” setting is “On”, it is not possible to do

“Tone Control” (vpage82) adjustment.

Reference Offset

Audyssey Dynamic EQ

referenced to the standard

ﬁlm mix level. It makes

adjustments to maintain

the reference response

and surround envelopment

when the volume is turned

down from 0 dB. However,

ﬁlm reference level is not

always used in music or

other non-ﬁlm content.

Dynamic EQ

Reference

Level Offset provides three

offsets from the ﬁlm level

reference (5 dB, 10 dB, and

15 dB) that can be selected

when the mix level of the

content is not within the

standard. Recommended

setting levels are shown at

right.

0dB (Film Ref) : This is the default setting and should be used when

listening to movies.

5dB : Select this setting for content that has a very wide dynamic range,

such as classical music.

10dB : Select this setting for jazz or other music that has a wider dynamic

range. This setting should also be selected for TV content as that is usually

mixed at 10 dB below ﬁlm reference.

15dB : Select this setting for pop/rock music or other program material

that is mixed at very high listening levels and has a compressed dynamic

range.

Setting is enabled when “Dynamic EQ

” is “On” (vpage84).

Dynamic Volume

Solve the problem of large

variations in volume level

between TV, movies and

Kommentare zu diesen Handbüchern

Keine Kommentare

Denon AVR-1613 Bedienungshandbuch Seite 87

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für AV-Receiver Denon AVR-1613